Notifier NFS2-3030 Manuel d'utilisateur télécharger pdf

This sheet must be framed and mounted adjacent to the control panel.

Document 52547 Rev B ECN 08-364 8/18/2008

Section 1 Operating Information

Normal Standby Operation.

1. Green POWER indicator lit steadily.

2. Red F

IRE ALARM indicator off.

3. Yellow T

ROUBLE indicators off.

Alarm Condition.

1. Red FIRE ALARM indicator lit.

2. Alarm signaling devices activated.

3. Option module (remote station or supplementary alarm relay) activated.

4. Alarm information visible on LCD (liquid crystal display).

Alarm Reset. After locating and correcting the alarm condition, reset

the control panel by pressing the S

YSTEM RESET switch.

Trouble Condition. Activation of trouble signal under normal

operation indicates a condition that requires immediate attention. Contact

your local service representative. Silence the audible signal by pressing the

CKNOWLEDGE switch. The trouble indicator will remain illuminated.

Section 2 NFS2-3030 Switch Functions

ACKNOWLEDGE. This silences the piezo sounder and changes all flashing

conditions to steady. It sends an acknowledge message to the printer and

history file. A

CKNOWLEDGE also automatically sends a special command to

silence piezo sounders on ACS Annunciators. If more than one event exists,

it advances the display to the next item and displays it until the

CKNOWLEDGE switch is pressed again. Only one press is necessary for

non-fire, trouble, or supervisory signals.

SIGNAL SILENCE. SIGNAL SILENCE turns off all silenceable circuits and

illuminates the S

IGNALS SILENCED indicator. It also sends a SIGNALS

ILENCED message to the LCD, printer, and history file. A subsequent alarm

will then resound the system.

Notes:

1. This system is programmed to inhibit signal silence for ____seconds.

2. This system is programmed to automatically silence alarm signal after

_____ minutes.

DRILL. The NFS2-3030 waits for the DRILL switch to be pressed for 2 seconds,

then turns on all silenceable circuits (all control modules/panel circuits that are

programmed silenceable for fire alarms), and turns off the S

IGNALS SILENCED

LED. This event shows on the LCD, printer, and History file.

Note: This switch is only available on NFS2-3030 with keypad/display.

SYSTEM RESET. Resets the control panel in standalone applications.

Resets panel when enabled in network applications.

LAMP TEST. Press and hold the switch to lamp-test the LEDs.

Section 3 LED Indicators

Controls Active. Green LED which illuminates when the NFS2-3030

assumes control of the network primary display.

Power . Green LED which illuminates when primary power is applied to

the control panel.

Fire Alarm. Red LED that flashes when one or more alarms occur.

Illuminates steadily after alarms are acknowledged, and turns off when

YSTEM RESET is pressed after alarm clears.

Pre-Alarm. Red LED that flashes when a pre-alarm threshold is reached.

Security. Blue LED that illuminates for a security alarm. LED turns off

after the alarm clears and S

YSTEM RESET is pressed.

Supervisory. Yellow LED that flashes when a Supervisory or Tamper

condition occurs, such as a sprinkler valve tamper condition. The LED

illuminates steady after conditions are acknowledged, and turns off when the

conditions are cleared. The Tamper indication will latch until S

YSTEM RESET

is pushed.

System Trouble. Yellow LED that flashes when one or more troubles

occur. Goes on steadily when A

CKNOWLEDGE is pressed, and turns off when

all trouble conditions are cleared.

Other Event. Yellow LED flashes when a process monitor, hazard alert

or weather alert occurs. Goes on steadily when A

CKNOWLEDGE is pressed,

and turns off when the condition is cleared.

Signals Silenced. Yellow LED that illuminates after SIGNALS

ILENCED has been pressed. Turns off when DRILL or SYSTEM RESET is

pressed.

Point Disabled. Yellow LED that illuminates when one or more points

are disabled. The LCD will indicate which points have been disabled. Turns

off when points are re-enabled.

CPU Failure. Yellow LED that illuminates if the microprocessor fails.

Section 4 NFS2-3030 Audible Sounder

Alarm. A continuous sounding tone.

Trouble, Disable, Prealarm. Two beeps per second.

Supervisory. Four beeps per second.

Security. Eight beeps per second.

Section 5 Periodic Testing and Maintenance

To ensure proper and reliable operation, system inspection and testing should

be scheduled monthly, or as required by NFPA 72 or local fire codes. A

qualified Service Representative should perform testing.

Before Testing: Notify fire department and/or central alarm receiving

station if alarm condition is transmitted. Notify facility personnel of the test

so alarm sounding devices are ignored during the test period. Physically

disconnect releasing devices.

Remote Connection Feature: ULC requires that devices such as

UDACT and TM-4 be disconnected during annual testing to prevent

transmission of false alarms.

UDACT: Disable by turning the internal AKS-1 keyswitch.

TM-4: Slide SW4 Disable All Output switch from “Enable” to “Disable.”

After Testing: Verify that remote-connection devices are turned back

on. Notify all fire, central station, and/or building personnel when testing is

complete. Re-connect releasing devices.

Section 6 Local Service Representative:

NAME: ________________________________________________

ADDRESS: _____________________________________________

TELEPHONE NUMBER: ________________________________

NFS2-3030 OPERATING INSTRUCTIONS

Résumé du contenu

Page 1

This sheet must be framed and mounted adjacent to the control panel.Document 52547 Rev B ECN 08-364 8/18/2008Section 1 Operating InformationNorm

Plus de documents pour Panneau de contrôle Notifier NFS2-3030

Voir le document Notifier NFS2-3030 Manuel d'utilisateur

Notifier NFS2-3030 Manuel d'utilisateur (24 pages)

Commentaires sur ces manuels

Pas de commentaire

Notifier NFS2-3030 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Panneau de contrôle Notifier NFS2-3030. Notifier NFS2-3030 User Manual Manuel d'utilisatio

Résumé du contenu

Plus de documents pour Panneau de contrôle Notifier NFS2-3030

Commentaires sur ces manuels

Produits connexes et manuels pour Panneau de contrôle Notifier NFS2-3030