DN-6923:B • 05/15/2009 — Page 1 of 2
XP10-M(A)
Ten-Input Monitor Module
Addressable Devices
DN-6923:B • H-352
General
The XP10-M ten-input monitor module is an interface
between a control panel and normally open contact devices
in intelligent alarm systems such as pull stations, security
contacts, or flow switches.
The first address on the
XP10-M
is set from 01 to 150 and
the remaining modules are automatically assigned to the
next nine higher addresses. Provisions are included for dis-
abling a maximum of two unused addresses.
The supervised state (normal, open, or short) of the moni-
tored device is sent back to the panel. A common SLC input
is used for all modules, and the initiating device loops share a
common supervisory supply and ground — otherwise each
monitor operates independently from the others.
Each XP10-M module has panel-controlled green LED indi-
cators. The panel can cause the LEDs to blink, latch on, or
latch off.
NOTE: Unless otherwise specified, the term XP10-M is used in
this data sheet to refer to both the XP10-M and the XP10-MA
(ULC-listed version)
.
Features
• Listed to UL Standard 864, 9th edition.
• Ten addressable Class B or five addressable Class A initi-
ating device circuits.
• Removable 12 AWG (3.31 mm²) to 18 AWG (0.821 mm²)
plug-in terminal blocks.
• Status indicators for each point.
• Unused addresses may be disabled.
• Rotary address switches.
• Class A or Class B operation.
• FlashScan® or CLIP operation.
• Flexible mounting options.
• Mounting hardware included.
Specifications
Standby current: 3.5 mA (SLC current draw with all
addresses used; if some addresses are disabled, the
standby current decreases).
Alarm current: 55 mA (assumes all ten LEDs solid ON).
Temperature range: 32°F to 120°F (0°C to 49°C) for UL
applications; –10°C to +55°C for EN54 applications.
Humidity: 10% to 85% noncondensing for UL applications;
10% to 93% noncondensing for EN54 applications.
Dimensions: 6.8" (172.72 mm) high x 5.8" (147.32 mm)
wide x 1.25" (31.75 mm) deep.
Shipping weight: 0.76 lb. (0.345 kg) including packaging.
Mounting options:
– CHS-6 chassis: Up to 6 modules.
– BB-25 cabinet: Up to 6 modules.
– BB-XP cabinet: One or two modules.
– CAB-4 Series cabinet: See DN-6857.
– EQ Cabinet Series: See DN-60229.
Wire gauge: 12 AWG (3.31 mm²) to 18 AWG (0.821 mm²).
Power-limited circuits must employ type FPL, FPLR, or
FPLP cable as required by Article 760 of the NEC.
XP10-M is shipped in Class B position; remove shunt for
Class A operation.
Maximum SLC wiring resistance: 40 or 50 ohms, panel
dependent.
Maximum IDC wiring resistance: 1500 ohms.
Maximum IDC voltage: 10.2 VDC.
Maximum IDC current: 240 µA.
Agency Listings and Approvals
The listings and approvals below apply to the XP10-M(A) Ten-
Input Monitor Module. In some cases, certain modules or
applications may not be listed by certain approval agencies, or
listing may be in process. Consult factory for latest listing
status.
• UL Listed: S635
• ULC Listed: S635 (XP10-MA)
• CSFM approved: 7300-0028:219
•FM approved
• MEA approved: 43-02-E
• Maryland State Fire Marshal approved: Permit #2106
6923xp10.jpg
(2 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels